- Bally:

	Bracket, backbox insert door stop/securing: $1.00 ea Units Available: 3 Manufacturer: Bally Factory Part #: P-6665-540 Our Part #: P-6665-540 Condition: Used Description: One of two brackets used which holds a screw used for latching backbox insert panel in closed position. Two used per game.
	Bracket, backbox lock mounting: $0.50 ea Units Available: 1 Manufacturer: Bally Factory Part #: P-3473-18 Our Part #: P-3473-18 Condition: Used Description: Bracket used for mounting backbox lock.
	Bracket, backbox insert door support: $1.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally Factory Part #: P-6442-190 Our Part #: P-6442-190 Condition: Used Description: Bracket used to support lower right corner of backbox insert panel.
	Bracket, backbox circuit board mounting: $1.00 ea Units Available: 2 Manufacturer: Bally Factory Part #: P-6442-260 Our Part #: BKT_BLYPC5 Condition: Used Description: Bracket used for PC circuit board mounting in backbox. 5 inches overall length, 4-1/2 inches between end screw hole and end nylon standoff mount. As used for smaller boards such as sound board and similar.
	Bracket, backbox circuit board mounting: $1.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally Factory Part #: P-6442-185 Our Part #: BKT_BLYPC75 Condition: Used Description: Bracket used for PC circuit board mounting in backbox. 7-1/2 inches overall length, 7 inches between end screw hole and end nylon standoff mount. As used for solenoid/regulator boards and lamp driver boards.
	Bracket, backbox circuit board mounting: $1.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally, Stern Factory Part #: P-6442-186 (Bally), 1B-505 (Stern) Our Part #: BKT_BLYPC10 Condition: Used Description: Bracket used for PC circuit board mounting in backbox. 10 inches overall length, 9-1/2 inches between end screw hole and end nylon standoff mount. As used for MPU board mounting in Bally and Stern solid-state games.
	Bracket, display module mounting: $7.50 ea Units Available: 1 Manufacturer: Bally, Stern Factory Part #: A-3843 (Bally) Our Part #: U19 Condition: Used Description: Display module mounting bracket, or "tray", as used on all Bally and Stern solid-state pinball games from approximately 1977 through 1985. Used unit, sold as pictured.
	Bracket, transformer/rectifier board panel mounting: $2.00 ea Units Available: 3 Manufacturer: Bally Factory Part #: P-6442-191 Our Part #: U68 Condition: Used Description: Mounts in right rear corner of backbox, vertically, and transformer/rectifier board panel connects to this via screws. Used part in good condition.
	Bracket, speaker/display panel latch: $5.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally, Williams Factory Part #: 01-8535 Our Part #: U92 Condition: Used Description: One of two brackets that attach to back side of speaker/display panel, as used on Bally and Williams pinballs, approx. 1987-1999. Holds panel to backbox, in upright position. Used part in good condition.

- Data East:

Bracket, backbox insert door securing: $1.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Data East Factory Part #: Unknown Our Part #: BKT_DEPBBINSSEC Condition: Used Description: Bracket which holds a screw used for latching backbox insert panel in closed position.

- Stern:

Bracket, display module mounting: $7.50 ea Units Available: 1 Manufacturer: Bally, Stern Factory Part #: Unknown Our Part #: U19 Condition: Used Description: Display module mounting bracket, or "tray", as used on all Bally and Stern solid-state pinball games from approximately 1977 through 1985. Used unit, sold as pictured.

- Williams:

	Bracket, upper backbox insert mounting: $2.50 ea Units Available: 2 Manufacturer: Williams Factory Part #: A-7984 Our Part #: A-7984 Condition: Used Description: Upper bracket used for holding backbox insert panel in Williams solid-state pinball games.
	Bracket, lower backbox insert mounting: $3.50 ea Units Available: 2 Manufacturer: Williams Factory Part #: A-7985 Our Part #: A-7985 Condition: Used Description: Lower bracket used for holding backbox insert panel in Williams solid-state pinball games.
	Bracket, backbox insert door stop: $0.50 ea - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #: 01-6664 Our Part #: 01-6664 Condition: Used Description: Stop bracket used in left corner of backbox insert panel. Mounts on top of A-7985 (above).
Sample	Bracket, backbox insert door mounting: $1.00 ea Units Available: 3 Manufacturer: Williams Factory Part #: 01-6571 Our Part #: 01-6571 Condition: Used Description: One of two brackets used on left side of backbox insert panel. These attach to brackets on the backbox interior and act as hinges, holding the insert panel in place. May or may not include mounting bolts, washers, screws.
	Bracket, backbox insert door alignment/securing: $1.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #: 01-6647 Our Part #: 01-6647 Condition: Used Description: One of two brackets used on right interior backbox wall to align & secure insert panel when in closed position.
	Bracket, backbox insert door alignment: $0.50 ea - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #: 01-6652 Our Part #: 01-6652 Condition: Used Description: Lower bracket on right edge of insert panel used to align panel to backbox interior bracket.
	Bracket, backbox mounting: $5.00 ea Units Available: 3 Manufacturer: Williams Factory Part #: 01-6646 Our Part #: 01-6646 Condition: Used Description: Cabinet connecting bracket that mounts on backbox bottom and latches to cabinet neck bracket when mounted. Holds backbox upright before mounting bolts are installed.
	Bracket, backbox circuit board mounting: $1.00 ea Units Available: 2 Manufacturer: Williams Factory Part #: 01-6639 Our Part #: 01-6639 Condition: Used Description: Bracket used for top of MPU board mounting in backbox. 10-1/2 inches overall length, 10 inches between PC board mounting screws, and 4-11/16 between each of the 3 screw mounting holes.
	Bracket, backglass latch support: $1.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: Unknown Our Part #: U39 Condition: Used Description: Bracket that screws to top inside of backbox and supports latch that locks backglass in place.
	Backglass locking tab: $1.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: Unknown Our Part #: U56 Condition: Used Description: Metal tab that screws to backglass locking latch bar and holds backglass in place when locked. Used in Williams games, late 1970's through mid 1980's. Used part in good condition.
	Bracket, speaker/display panel latch: $5.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally, Williams Factory Part #: 01-8535 Our Part #: U92 Condition: Used Description: One of two brackets that attach to back side of speaker/display panel, as used on Bally and Williams pinballs, approx. 1987-1999. Holds panel to backbox, in upright position. Used part in good condition.

- All/Most Makes & Models:

Relay, DPDT: $10.00 ea Units Available: 1 Manufacturer: MANY Factory Part #: Undetermined Our Part #: U254 Condition: Used Description: Double-pole double-throw relay. As used for control of lamps, flippers, and other devices in many makes and models. Used part in good condition.

- Bally:

Heat sink, Q20, solenoid/regulator board: $5.00 ea Units Available: 4 Manufacturer: Bally, Stern Factory Part #: Undetermined Our Part #: U177 Condition: Used Description: Large heat sink used in upper right corner on solenoid/regulator PC board in Bally and Stern solid-state pinball games, 1977-1985. Holds Q20 regulator for 5-volt power supply circuitry. Used part in good condition.

- Data East:

Data East 50V Flipper Power Supply Board: $50.00 ea Units Available: 1 Manufacturer: Data East Factory Part #: 520-5001-00 Our Part #: 520-5001-00 Condition: Used, tested, working Description: Compare to new at $79! 50 volt flipper power supply board as used in many early Data East games including Laser War and more. Tested and working. Can also be used in Williams games in place of # C-9939.

- Gottlieb:

Gottlieb/Premier Pinball Auxillary Power Supply Board: $5.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Gottlieb Factory Part #: Unknown Our Part #: BB_BOARD7 Condition: Used Description: Possibly from a Gottlieb "Victory" pinball. Auxillary power supply unit. Appears clean, complete. Sold as-is, untested.

- Stern:

Heat sink, Q20, solenoid/regulator board: $5.00 ea Units Available: 4 Manufacturer: Bally, Stern Factory Part #: Undetermined Our Part #: U177 Condition: Used Description: Large heat sink used in upper right corner on solenoid/regulator PC board in Bally and Stern solid-state pinball games, 1977-1985. Holds Q20 regulator for 5-volt power supply circuitry. Used part in good condition.

- Williams:

	Williams 50V Flipper Power Supply Board: $50.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: C-9939 Our Part #: C-9939 Condition: Used, tested, working Description: 50 volt flipper power supply board as used in many Williams System 9 and System 11 games including Space Shuttle, High Speed, F-14 Tomcat and more. Tested and working. Can also be used in Data East games in place of # 520-5001-00.
- Sample -	Williams Switched Lamp Filter Capacitor: $15.00 ea Units Available: 2 Manufacturer: Williams Factory Part #: Unknown Our Part #: U163 Condition: Used Description: This is the large capacitor that mounts on the bottom panel of the backbox interior, used on Williams solid-state pinball games from 1977 to mid-1980's. This capacitor filters the power used for the feature or "switched" lamps in the game. Most are rated at 30,000uF 25vdc, although values may vary. May or may not included mounting bracket.
	Light control relay and mounting bracket: $15.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: Unknown Our Part #: U208 Condition: Used Description: Relay that mounts on bottom panel in backbox and controls general illumination lighting throughout the game. Used in several Williams solid-state pinball games before 1981 including Blackout and early models of Black Knight. Includes mounting bracket. Used part in good condition.
	Solenoid/motor control relay: $7.50 each - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #'s: Unknown Our Part #: U238 Condition: Used Description: Relay used for control of various solenoids and/or motors in many Williams games including High Speed and others. Used part in good condition.
	Lamp Matrix Power Resistor- 27 ohm, 2-watt: 75¢ each Units Available: 4 Manufacturer: Williams Factory Part #'s: Unknown Our Part #: U365 Condition: Used Description: Original metal-film 2-watt power resistor as used in lamp matrix driver circuitry on driver board in Williams L3-L7 pinball games. Used part in good condition. Also available new: See upgraded 5-watt version (part # RES27-5W) available on our Electronic Parts page. 5-watt units run cooler and help protect your board from heat damage.

	Hinge, backbox, left: $10.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Data East Factory Part #: Unknown Our Part #: HIN_DEPBBL Condition: Used Description: Backbox hinge (left side). Connects backbox to main cabinet. Includes main cabinet mounting bolt, sleeve, nut, and washers.
	Hinge, backbox, right: $10.00 ea - SOLD - Units Available: 0 Manufacturer: Data East Factory Part #: Unknown Our Part #: HIN_DEPBBR Condition: Used Description: Backbox hinge (right side). Connects backbox to main cabinet. Includes main cabinet mounting bolt, sleeve, nut, and washers.

	Latch, backbox insert door securing: $5.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally Factory Part #: P-372-6 Our Part #: P-372-6 Condition: Used Description: One of two latches used which slips over a screw and latches backbox insert panel in closed position. Two used per game.
	Latch, backbox insert door securing: $3.00 ea Units Available: 3 Manufacturer: Williams Factory Part #: Unknown Our Part #: 01-6655 Condition: Used Description: Latch used on insert panel to secure panel in closed position.
	Armature, backglass lock assembly: $7.50 ea Units Available: 1 Manufacturer: Williams Factory Part #: A-7993 (lock cam), A-8044 (link) Our Part #: A-8044 Condition: Used Description: 2 piece lock cam and link assembly used for backglass lock.

	Bezel / shroud, single, backbox lamp: 50¢ ea - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #: Unknown Our Part #: BEZ_BBLAMP1 Condition: Used Description: White plastic bezel / shroud used around select single feature lamps on backbox insert panel.
	Bezel / shroud, double, backbox lamp: 50¢ ea - SOLD OUT - Units Available: 0 Manufacturer: Williams Factory Part #: Unknown Our Part #: BEZ_BBLAMP2 Condition: Used Description: White plastic bezel / shroud used around groups of 2 feature lamps on backbox insert panel.
	Bezel / shroud, double, backbox lamp: 50¢ ea Units Available: 1 Manufacturer: Williams Factory Part #: Unknown Our Part #: BEZ_BBLAMP4 Condition: Used Description: White plastic bezel / shroud used around groups of 4 feature lamps on backbox insert panel.
	Lamp socket, white, backbox insert panel: $3.00 ea Units Available: MANY Manufacturer: Bally, Williams Factory Part #: Unknown Our Part #: U297 Condition: Used Description: Press-in type lamp socket for wedge-base bulbs. White molded plastic. As used in many Bally and Williams pinball games. Mounts in insert panel behind backglass. Holds wedge-base bulb such as #555 and similar. Used in many games in early 1990's including Twilight Zone and more. Wires simply press in from behind. Used part in good condition.
	Lamp socket, black, backbox insert panel: $3.00 ea Units Available: MANY Manufacturer: Bally, Williams Factory Part #: Unknown Our Part #: U298 Condition: Used Description: Press-in type lamp socket for wedge-base bulbs. Black molded plastic. As used in many Bally and Williams pinball games. Mounts in insert panel behind backglass. Holds wedge-base bulb such as #555 and similar. Used in many games in early 1990's including Twilight Zone and more. Wires simply press in from behind. Used part in good condition.

Bushing, backglass lock latch: $1.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: 02-3970 Our Part #: 02-3970 Condition: Used Description: Metal spacer washer used to mount left end of backglass latch in top of backbox.

Bally Doctor Who Dalek red domes: $3.00 / set Units Available: 1 set Manufacturer: Bally Factory Part #: Unknown Our Part #: U256 Condition: Used Description: Set of two red plastic domes for Bally Doctor Who pinball. These two domes go on the top of the Dalek on the top of the backbox. Sold as a set of 2 pieces- one is dented/damaged, the other is in excellent condition. Used parts sold as pictured.

- Bally:

Replay knocker assembly: $25.00 - SOLD OUT - Units Available: 0 Manufacturer: Bally Factory Part #: AS-2402-12 Our Part #: U148 Condition: Used Description: Replay knocker assembly with coil and plunger. As used in Bally solid-state pinball games. Can be used in other makes/models as well. Includes 26-1200 coil with diode. Used part in good condition. (Coil wrapper color may vary.)

Sample

Score Display, 128 x 32 Dot-Matrix - Used: $85.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Many Factory Part #: Unknown Our Part #: UDMD1 Condition: Used, Working, As-Is Description: 128 x 32 dot-matrix score display unit. Used part, 100% working. Fits/works in most later-model games, approx. 1991-present (Click here for a list of games that use this display). Exact detailed condition varies from used unit to used unit. Most units may have some light-to-moderate signs of "burn in" from past use. Sold tested/working, as-is, no warranty. All sales are final- no returns, exchanges, or refunds. We also carry new displays. Click here for more info. NO RETURNS/EXCHANGES/REFUNDS ON USED DISPLAYS - TESTED AND VERIFIED 100% WORKING BEFORE SHIPPING - ALL SALES ARE FINAL INTERNATIONAL SHIPPING: Additional cost may be required to ship outside the U.S. due to weight and size. E-mail us with your shipping address if you need a quote on international shipping costs.

Bracket, display module mounting: $3.00 ea Units Available: 2 Manufacturer: Bally, Stern Factory Part #: Unknown Our Part #: U19 Condition: Used Description: Display module mounting bracket, or "tray", as used on all Bally and Stern solid-state pinball games from approximately 1977 through 1985. Used unit, sold as pictured.

	Bally Score Reel Assembly: $10.00 - SOLD OUT - Units Available: 0 Manufacturer: Bally Factory Part #: AS-1900-104 Our Part #: AS-1900-104 Condition: Used Description: 4-inch score reel assembly from a Bally electro-mechanical (EM) pinball. Commonly used in games throughout the 1970's. Complete as shown, untested, as-is. Does not use printed circuit board. Has CD-29-1600 coil.
	Williams 4-Inch Score Reel: $4.00 ea Units Available: 1 Manufacturer: Williams Factory Part #: Unknown Our Part #: WMS_REEL4 Condition: Used, good Description: 4-inch plastic score reels for use in Williams electro-mechanical pinballs, early to late 1970's. Good condition.

Speaker, backbox speaker/display panel: $10.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally, Williams Factory Part #: Unknown Our Part #: U160 Condition: Used Description: This is the smaller of the two speakers used on the back side of the speaker/display panel in the backbox of many Bally and Williams later-model pinball games, including late System 11 games up through WPC games. Measures approx. 3-1/2 inches in diameter. Used part in good condition. Sold working.

Speaker, backbox speaker/display panel: $10.00 ea - SOLD OUT - Units Available: 0 Manufacturer: Bally, Williams Factory Part #: Unknown Our Part #: U211 Condition: Used Description: This is one of two speakers used on the back side of the speaker/display panel in the backbox of many Bally and Williams later-model pinball games, including late System 11 games up through WPC games. Measues approx. 3-1/2 inches in diameter. Used part in good condition. Sold working.

Stepper unit coil plunger- side-notched: $2.00 ea Units Available: 1 Manufacturer: Unknown Factory Part #: Unknown Our Part #: U235 Condition: Used Description: Short coil plunger with side-notch. As used for stepper units in electro-mechanical pinball games. Measures 1-5/8 inches in length, 7/16 inch diameter. Notch is 1/4 inch in length. Used part in good condition.

Please see our Used Cabinet Parts page for transformer listings.